editline(3)


NAME
     editline - command-line editing library with history

SYNOPSIS
     char *readline(char *prompt)

DESCRIPTION
     Editline is a library that provides an line-editing interface  with  text
     recall.   It  is  intended  to  be  compatible  with the readline library
     provided by the Free Software Foundation, but much smaller.  The bulk  of
     this manual page describes the user interface.

     The readline routine returns a line of text  with  the  trailing  newline
     removed.   The  data is returned in a buffer allocated with malloc(3), so
     the space should be released with free(3) when  the  calling  program  is
     done with it.  Before accepting input from the user, the specified prompt
     is displayed on the terminal.

     Each line returned is copied to the  internal  history  list,  unless  it
     happens to be equal to the previous line.

  User Interface
     A program that uses this library provides  a  simple  emacs-like  editing
     interface  to  its  users.  A line may be edited before it is sent to the
     calling program by typing either control characters or escape  sequences.
     A  control  character, shown as a caret followed by a letter, is typed by
     holding down the ``control'' key while the letter is typed.  For example,
     ``^A''  is  a  control-A.   An  escape  sequence is entered by typing the
     ``escape'' key followed by one or more characters.   The  escape  key  is
     abbreviated  as  ``ESC.''  Note that unlike control keys, case matters in
     escape sequences; ``ESC F'' is not the same as ``ESC f''.

     An editing command may be typed anywhere on the line,  not  just  at  the
     beginning.  In addition, a return may also be typed anywhere on the line,
     not just at the end.

     Most editing commands may be given a  repeat  count,  n,  where  n  is  a
     number.   To  enter  a repeat count, type the escape key, the number, and
     then the command to execute.  For  example,  ``ESC 4 ^f''  moves  forward
     four  characters.  If a command may be given a repeat count then the text
     ``[n]'' is given at the end of its description.

     The following control characters are accepted:
          ^A       Move to the beginning of the line
          ^B       Move left (backwards) [n]
          ^D       Delete character [n]
          ^E       Move to end of line
          ^F       Move right (forwards) [n]
          ^G       Ring the bell
          ^H       Delete character before cursor (backspace key) [n]
          ^I       Complete filename (tab key); see below
          ^J       Done with line (return key)
          ^K       Kill to end of line (or column [n])
          ^L       Redisplay line
          ^M       Done with line (alternate return key)
          ^N       Get next line from history [n]
          ^P       Get previous line from history [n]
          ^R       Search backward (forward if [n]) through history for text;
                   must start line if text begins with an uparrow
          ^T       Transpose characters
          ^V       Insert next character, even if it is an edit command
          ^W       Wipe to the mark
          ^X^X     Exchange current location and mark
          ^Y       Yank back last killed text
          ^[       Start an escape sequence (escape key)
          ^]c      Move forward to next character ``c''
          ^?       Delete character before cursor (delete key) [n]

     The following escape sequences are provided.
          ESC ^H   Delete previous word (backspace key) [n]
          ESC DEL  Delete previous word (delete key) [n]
          ESC SP   Set the mark (space key); see ^X^X and ^Y above
          ESC .    Get the last (or [n]'th) word from previous line
          ESC ?    Show possible completions; see below
          ESC <    Move to start of history
          ESC >    Move to end of history
          ESC b    Move backward a word [n]
          ESC d    Delete word under cursor [n]
          ESC f    Move forward a word [n]
          ESC l    Make word lowercase [n]
          ESC m    Toggle if 8bit chars display normally or with ``M-'' prefix
          ESC u    Make word uppercase [n]
          ESC y    Yank back last killed text
          ESC v    Show library version
          ESC w    Make area up to mark yankable
          ESC nn   Set repeat count to the number nn
          ESC C    Read from environment variable ``_C_'', where C is
                   an uppercase letter

     The editline library has a small macro facility.  If you type the  escape
     key  followed  by  an  uppercase  letter,  C,  then  the  contents of the
     environment variable _C_ are read in as if you  had  typed  them  at  the
     keyboard.  For example, if the variable _L_ contains the following:
          ^A^Kecho '^V^[[H^V^[[2J'^M
     Then typing ``ESC L'' will move to the beginning of the  line,  kill  the
     entire line, enter the echo command needed to clear the terminal (if your
     terminal is like a VT-100), and send the line back to the shell.



     The editline library also does filename  completion.   Suppose  the  root
     directory has the following files in it:
          bin    vmunix
          core   vmunix.old
     If you type ``rm /v'' and then the tab key.  Editline  will  then  finish
     off  as  much  of  the name as possible by adding ``munix''.  Because the
     name is not unique, it will then beep.  If you type the escape key and  a
     question  mark,  it  will  display  the  two choices.  If you then type a
     period and a tab, the library will finish off the filename for you:
          rm /v[TAB]munix.TABold
     The tab key is shown by ``[TAB]'' and the automatically-entered  text  is
     shown in italics.

BUGS AND LIMITATIONS
     Doesn't know how to handle multiple lines.

AUTHORS
     Simmule  R.  Turner  <uunet.uu.net!capitol!sysgo!simmy>  and  Rich   $alz
     <rsalz@osf.org>.    Original   manual   page   by   DaviD   W.  Sanderson
     <dws@ssec.wisc.edu>.